Purelink RTLS Visibility receivers

RECEIVERS

VISIBILITY RECEIVERS
PLK-VRF015-10

Purelink's visibility receiver PLK-VR0F15-10 covers large areas for RTLS applications. While providing coverage over 40,000 m2, it identifies for over 10,000 badges, tags and sensors the zones where they are. A zone can be as small as 20 m x 20 m or as large as 200 m x 200 m.

The Visibility receiver PLK-VRF015-10 is ultra sensitive and benefits from the same Purelink tri-band technology as the location receiver. It is designed to effectively cover large areas in buildings, factories, hospitals and metallurgical plants. Its unrivaled sensitivity even detects the tags and badges signals in the most hostile environments.

The largest RTLS coverage of the market

The outstanding performance of the PLK-VRF015-10 receivers is used to provide the best RTLS coverage on the market. The dual independent antenna in MIMO technology ensures maximum communication robustness. This innovative approach ensures high redundancy. No matter what your working environment is, the PLK-VRF015-10 is designed to process each badge and tag’s transmission, reliably. The antennas of the receiver can be oriented in different directions to optimize the signal strength or to maximize radio coverage for your application.

The PLK-VRF015-10 delivers two RTLS services, or modes, with BlueFairyTM Computing Engine:

  • You can configure it for optimal coverage for Location by zone.
  • You can configure your PLK-TR015-10 for Checkpoint Mode.

The PLK-VRF015-10 and PLK-TR015-10 are the only infrastructure equipment necessary to cover very large areas on the floors of a building or a parking lot for location-based applications. A few receivers are sufficient to cover entire floors of an office building, hospital or airport, while identifying the areas where there were people or equipment. To increase the coverage, just add receivers. The PLK-VRF015-10 uses the existing communications infrastructure to route location data to BlueFairyTMComputing Engine enabling the deployment of applications for personnel protection, security and process optimization

The receiver-VRF015 PLK-10 is specially designed for location by zone. It integrates Purelink’s latest tri-band technology, that is 5.8 GHz and 2.4 GHz for communications with the badges and WiFi for data transport over the network. The PLK-VRF015-10 offers three options:

  • Option 1: WiFi 802.11n
    The WiFi option increases the agility of the receiver to transport badges data without installing network cable. Receivers PLK-TR015-10 are seen by your network as a single Ethernet client.This option allows you to deploy location-based applications at low cost without increase the number of Access Points in your existing wireless network.
  • Option 2: Power over Ethernet
    Fully compatible with IEEE 802.3af/at standard, Power Over Ethernet (POE) option provides power to the receiver PLK-TR015-10 with any POE Switch.
  • Option 3: Combadge Module
    The Combadge module control PLK-NT030-20BZ audible badges and PLK-SE030-OP1 visual feedback badges and over 250 m distance. For example, in location-based applications, when a person accesses a restricted area, the receiver can make the badge ring or flash.

Technical Specifications

Processing capacity 10 000 badges/tags/sensors per second
2 services Visibility (tracking by zone)
Checkpoint
Outdoor Coverage 40 000 m2 (200 m x 200m)
430 336 pi2 (656 pi x 656 pi)
INdoor Coverage * 6 400 m2 (80 m x 80 m)
68 889 pi2 (262 pi x 262 pi)
Network Interface LAN/ WLAN Ethernet
Option 1 Wi-Fi Access Point/ Router
Option 2 Power over Ethernet
Option 3 Combadge module to send commands
to badges and tags
Purelink long-range active rfid Visibility Receivers
Available in 3 colors
 
PLK-VRF015-10
Starting from*: 899.99$
PDF  Download Spec Sheet
Purchase
Green Program
..
Videos >
Products >
Applications >

*All prices are in USD. Prices are subject to change without notice.

SOFTWARE >